Original parts and components for Bull machines.
Replacement electric motor for the spiral mechanism in the Bull Classic vending machine. Swap it when the spiral turns slowly, jerks or stops moving altogether.
Main control board for the Bull Classic vending machine. Runs payments, display and sensors; ships with firmware preloaded.
Pair of infrared drop sensors for the Bull Classic dispensing tray. Sold and replaced as a pair so alignment and timing stay accurate.
Interior LED lighting for the Bull Classic vending machine. Replace it when output dims, flickers or fails entirely.
Replacement 5-inch display for the Bull Classic vending machine control panel. Swap it after cracked glass, dead pixels or a fully blank screen.
Digital probe that monitors the internal temperature of Bull Classic. Drives the cooling cycle and reports when the machine drifts outside its setpoints.
Membrane numeric keypad with its harness. Use it when key response drops off or the link to the main board breaks.
Single-slot motor for one specific spiral position in Bull Classic. The cheaper option when only one dispenser has failed.
Standalone infrared drop sensor for Bull Classic. Use it when only one side of the pair needs replacing.
Replacement protective fuse for Bull Classic low-voltage electronics. Cheap part, always handy to keep one on hand.
Main power supply for the Bull Classic vending machine. Swap it on random reboots, a blank display or a machine that won't power on.
Electromagnetic relay that switches the cooling compressor and lighting in Bull Classic. When it fails it usually clicks repeatedly with no follow-through.
Densest spiral for Bull Classic, 66 mm diameter, 23 mm pitch. Holds 15 narrow items per row, like bars or gum. Ships as a pair.
Tight spiral for Bull Classic, 66 mm diameter, 33 mm pitch. Holds 11 smaller items per row, like chocolate bars or small biscuits. Ships as a pair.
Versatile spiral for Bull Classic, 66 mm diameter, 55 mm pitch. Holds 7 medium items per row, like chip bags or larger chocolates. Ships as a pair.
Balanced spiral for Bull Classic, 66 mm diameter, 66 mm pitch. Holds 6 medium-width items per row, such as bulkier chip bags. Ships as a pair.
Open-pitch spiral for Bull Classic, 66 mm diameter, 77 mm pitch. Holds 5 wider items per row, like larger chip bags or biscuit packs. Ships as a pair.
Widest spiral pitch for Bull Classic, 66 mm diameter, 100 mm pitch. Holds 4 bulky items per row, like sandwiches or cereal boxes. Ships as a pair.
Replacement security lock with key for Bull Classic doors. Use it after a lost key or when relocating a machine to a new spot.
Mechanical switch that tells the Bull Classic control board whether the door is open. When it fails, the machine often reports the door as permanently open.
Price-label kit for Bull Classic with 8888 character cards and 48 ready-to-use price tags. Use it when pricing changes or originals are losing legibility.
Wiring harness between the main board and spiral motors in Bull PRO, LIFT and Bull Fresh & Frost. Use it for broken conductors or damaged connectors.
Wiring for the 6th bin in the Bull PRO, LIFT and Bull Fresh & Frost lineup. Usually the culprit when the whole sixth row falls silent while the rest still work.
Wiring for the 5th bin in the Bull PRO, LIFT and Bull Fresh & Frost lineup. Replace it for a torn-out connector or when the entire fifth row stops responding.
Wiring for the 4th bin in the Bull PRO, LIFT and Bull Fresh & Frost lineup. Use it when the whole fourth row of slots goes silent at once.
Wiring for the 3rd bin in the Bull PRO, LIFT and Bull Fresh & Frost lineup. Replace it when the third row suddenly stops responding.
Wiring for the 2nd bin in the Bull PRO, LIFT and Bull Fresh & Frost lineup. Usually the culprit for sudden failures of the entire second shelf.
Wiring for the 1st bin in the Bull PRO, LIFT and Bull Fresh & Frost lineup. A common candidate for broken conductors after service work.
Wiring for the 0th bin in the Bull PRO, LIFT and Bull Fresh & Frost lineup. Use it for damaged connectors on the base row of slots.
MDB cable between payment terminals and the control board in Bull PRO, LIFT and Bull Fresh & Frost vending machines. When it fails the machine stops accepting contactless payments and coins.
Main control board for Bull PRO, LIFT and Bull Fresh & Frost vending machines. Runs dispensing, payments, cooling and sensors. After install you'll need to re-run pricing and pair the payment terminal.
Transmitting board for the infrared drop sensor in Bull PRO, LIFT and Bull Fresh & Frost. Replace it when the RX side is working but no signal is reaching it.
Receiving board for the infrared drop sensor in Bull PRO, LIFT and Bull Fresh & Frost. Without it the machine can't confirm a drop and refunds the customer.
LED light strip for the combo machines in Bull PRO, LIFT and Bull Fresh & Frost. Replace it when output dims, flickers, or fails entirely.
Electronic temperature controller for the cooling loop in Bull PRO, LIFT and Bull Fresh & Frost vending machines. When it fails the machine cools continuously or can't hold the setpoint.
Replacement 5-inch color display for the Bull PRO, LIFT and Bull Fresh & Frost control panels. Use it after cracked glass or a fully unresponsive screen.
Replacement keyboard for Bull PRO, LIFT and Bull Fresh & Frost. Under heavy traffic the most-used keys lose responsiveness first.
Protective circuit breaker for the main power circuit in Bull PRO, LIFT and Bull Fresh & Frost. Installation should be left to a service technician.
Single-slot motor for one specific spiral position in Bull PRO, LIFT and Bull Fresh & Frost. The cheaper option when only one dispenser has failed.
Double motor for wider spiral slots in Bull PRO, LIFT and Bull Fresh & Frost. Synchronously turns two adjacent spirals for larger or bulkier products.
Complete cooling unit with shelf for Bull PRO, LIFT and Bull Fresh & Frost vending machines. The most involved service item; best deployed during a full machine overhaul.
Replacement tempered glass doors for Bull PRO, LIFT and Bull Fresh & Frost. Install with two people; the part is heavy and fragile.
Complete door lock set for Bull PRO, LIFT and Bull Fresh & Frost including the cylinder, keys, and mounting hardware. Ready for direct install.
Guide rail that holds cans and bottles in place inside Bull PRO, LIFT and Bull Fresh & Frost slots. Replace it on bends, cracks, or visible wear on the guide surfaces.
Widest spiral for Bull PRO, LIFT and Bull Fresh & Frost combo machines, 71 mm diameter, 113 mm pitch. Holds 4 bulky items, like sandwiches or cereal boxes per row. Ships as a pair.
Wide spiral for Bull PRO, LIFT and Bull Fresh & Frost combo machines, 71 mm diameter, 85 mm pitch. Holds 5 wider items, like larger chip bags per row. Ships as a pair.
Mid-open spiral for Bull PRO, LIFT and Bull Fresh & Frost combo machines, 71 mm diameter, 72 mm pitch. Holds 6 bulkier chip bags and similarly wide goods per row. Ships as a pair.
Versatile spiral for Bull PRO, LIFT and Bull Fresh & Frost combo machines, 71 mm diameter, 65 mm pitch. Holds 7 medium items, like larger chocolates or cans per row. Ships as a pair.
Denser spiral for Bull PRO, LIFT and Bull Fresh & Frost combo machines, 71 mm diameter, 51 mm pitch. Holds 8 narrow items, like smaller chocolates or standard-width cans per row. Ships as a pair.
Tight spiral for Bull PRO, LIFT and Bull Fresh & Frost combo machines, 71 mm diameter, 34 mm pitch. Holds 12 narrow items, like bars, gum, or small biscuits per row. Ships as a pair.
Densest spiral for Bull PRO, LIFT and Bull Fresh & Frost combo machines, 71 mm diameter, 25 mm pitch. Holds 16 very narrow items, like bars, gum, or thin tins per row. Ships as a pair.
Nayax payment terminal for vending machines, handling card and mobile payments. Cloud transaction management and integration with the Nayax vending and parking ecosystem.
Banknote acceptor for vending machines with recognition of major world currencies. Fast detection and strong counterfeit protection.
Professional bill acceptor supporting all EUR denominations. Quiet operation and stable performance under heavy use.
L83 bill acceptor with a water-tight front mask. Suitable for indoor and outdoor installations.
L83 variant with 3 or 6 stacker modules. For locations with higher cash transaction volume.
Banknote acceptor from the NBA series. Compact form factor with fast banknote validation.
XBA is the successor to NBA with improved counterfeit protection. Modular design and easy maintenance.
SCA1 without stacker for kiosk applications. Front-mask variant gives a clean install look.
SCA1 banknote acceptor without stacker. A budget-friendly option for small and mid-size vending machines.
BR2300 recycler with stacker. Saves change and reduces cash refill frequency.
NDE 1000 banknote acceptor with a 1000-note stacker. For locations with high cash volume.
Note Deposit Recycler that recycles incoming banknotes. Suited for bill changers and casinos.
Universal coin acceptor UCA1 and UCA2. Recognises up to 16 coin types simultaneously.
Coin sorter accessory for the UCA coin acceptor. Sorts coins by denomination into tubes.
RB-1 bill recycler for locations that dispense change. Pays out and accepts notes through the same mechanism.
MTB coin changer with tube hoppers. For change machines in vending and parking.
SP1-BDS bill changer. Accepts a banknote and dispenses the equivalent in coins.
Leonid coin hopper for change payout. Tough build holds up to vibration even in outdoor machines.
Slimmer version of the Leonid coin hopper. Fits tight enclosures in smaller vending machines.
P77 note dispenser for paying out notes. Holds hundreds of notes with fast dispense.
P77 P5 with expanded stacker. For locations that frequently pay out larger sums.
H2-7EA2 electronic counter with a 7-segment display. Tracks operation counts and runtime hours.
FP-004 programmer for configuring ICT devices. Updates firmware and settings over serial.
Generic GP-83 programmer for a wide range of ICT coin and bill devices.
CSD-600 thermal printer for receipts and confirmations. Quiet operation, auto cutter.
EWTC-310 3-inch thermal printer for kiosks and vending machines. Quiet and built for continuous duty.
EWTJ-680 thermal printer with presenter. Holds the receipt until the customer takes it.
EWTJ-700 builds on the EWTJ series. Faster print speed and longer cutter life.
Modular EWTK printer series for integrators. Choose 2-inch or 4-inch paper width.
EWTL-3000 industrial printer for demanding sites. Large paper capacity.
CVD-300 and CVD-1000 card dispensers. The CVD-1000 holds ten times the capacity of the CVD-300.
DCM5 document checker. Scans and verifies ID cards or vouchers at the machine entry point.
